- COLIBRI LIGHTER REPAIRS HOW TO
- COLIBRI LIGHTER REPAIRS PDF
- COLIBRI LIGHTER REPAIRS MANUAL
- COLIBRI LIGHTER REPAIRS CRACK
I am looking forward to giving this “new” lighter a try to see how it works and if it is one that I will use or if it is one that will be sold off to finance a new one. The ease with which it can be lit makes it a pleasure to use. It is a very light weight piece that is thin enough to fit in my pocket or my pipe case with no trouble. The lighter includes a tamper in the bottom that can be extended to tamp down the tobacco. I adjust the fill tube so that it did not stick open and allow the butane to escape.
COLIBRI LIGHTER REPAIRS MANUAL
Using the manual I adjusted the flame on the lighter to extend it further from the lighter and enable me to use it in lighting my pipe. While none of the drawings are the lighter I have the adjustments are nonetheless present in the photos. We also have a large selection of pipes and pipe tobaccos, Arabic tobaccos. As well as being a specialist lighter repair centre we have an extensive range of tobaccos, cigarettes and cigars.
COLIBRI LIGHTER REPAIRS PDF
I have included both the link to the PDF file and the two page document itself below. SALTS was founded here in Coventry in 1916 by Harry Salt and since 1919 we have been the World’s leading independent specialist lighter repair centre. Repaired or replacement lighters shipped to you from Colibri are shipped. INVOLVED ARE UNKNOWN BUT IT WAS SEVEN YEARS OLD AND HAD NO HISTORY OF REPAIRS. Colibri Lighter Repair Parts Colibri EVO Lighter and S-Cut Carbon Fiber. Sure enough the instructions included a guide for operating and adjusting the lighter I had found. FLAME - WHEN IT BURNS - DOES NOT PERFORM AS COLIBRI LIGHTER FLUID DOES. There I found a PDF of the instructions for a wide variety of their lighters. I went online and found the Colibri site.
COLIBRI LIGHTER REPAIRS HOW TO
I had no idea how to adjust the flame as there were not any instructions left in the box with the lighter. I was able to get a very small flame from the lighter but it did not extend far enough away from the lighter to light a pipe. There was a slight hissing that came from the filling tube on the bottom of the lighter so I used a small tipped screwdriver to adjust that valve. I filled it with Colibri Butane and pulled the slide down to see if I could get a flame. Sliding the bar downward ignites the butane. There is not a flint in the lighter and no spark wheel. The top 2/3 of the slide is grooved so that it is easy to move downward. There is no wheel that is struck to light the flame, rather the bar shown on the right side of the photo above is slid downward and the flame ignites. It can easily be adjusted to not damage the bowl of a pipe.
The flame comes out on the side of the lighter and is a soft torch flame. It has a brushed steel finish on both sides and the edges are polished stainless. This week I was looking for a pipe I had put in my desk and though I did not find the pipe I did find the lighter and took it out and had a look at it. I had not given it a thought or even filled it or tried it out. Somehow in one of the cleanups the girls in my household did on my study and desk top the lighter was put away and I totally forgot about it. I figured it was a bit of as steal so I grabbed it and brought it home. It was in a junk shop and I picked it up for around $20. Thanks for all the suggestions and if anyone else has similar problems, I'd be more than happy to try to help.Several years ago on one of my pipe hunts I came across this unused, still in the box Colibri Electro-Quartz lighter. Either way, I won't get too upset, now this is just something to tinker with.However, I am VERY excited about getting the other one up and running. If so, I'll probably fill it up with gas and let it sit for a few weeks and see how the glue holds up. After the glue dries I'm going to add a VERY little bit of butane and see if it lights. I tried to fill it with superglue, but I'm not sure if the glue can withstand the pressure - and I'm not sure that thats a risk I want to take (read hand-grenade). The spark was good but I had bled it awhile back (for shipping) so I tried to refill and butane shot out the crack.
COLIBRI LIGHTER REPAIRS CRACK
I managed to put it all back together and it works like new, nice big spark and a gorgeous dual flame.Īs for the small cigarette lighter, once i took it apart I saw there was a crack in the plastic casing (where the butane goes) - not good. I paid particular attention to the metal striker, because it was sooted over pretty bad and I think that and the flint were the problem. I also took out the flint and added a new one.
The CEO version I was able to scrub everything with an old toothbrush and a but of vodka and then hit with compressed air. So I took a gamble and took apart both of them.
0 kommentar(er)
